Adjust the parameter of motor of multihead weigher

Adjustment method of motor parameter. The motor mode has four types of code: 1,2,3,4 -Motor mode 1 is the movement way of 100 steps for motor -Motor mode 2 is the movement way of 96 steps for motor -Motor mode 3 is the movement way of 88 steps of motor -Motor mode 4 is the [...]

By |2024-05-11T17:49:10+00:00May 10th, 2024|Troubleshooting|0 Comments

How to solve the problem-Precision on multihead weigher is not good

If you are running a business that relies on accurate weight measurements, then you know that a multihead weigher is an essential piece of equipment. However, if your current machine is not giving you the level of precision that you need, don't worry - there are ways to improve it! In this blog post, we [...]

By |2024-05-11T17:49:04+00:00May 9th, 2024|Troubleshooting|Comments Off on How to solve the problem-Precision on multihead weigher is not good

Multihead weigher main vibrator replacement steps

Remove all feed hopper and feeder pan of multihead weigher Record the location of the waterproof cover so that you can quickly mount it back to the same location Remove all dust ring of waterproof cover Find the solid screw on the waterproof cover and remove it all Then lift the waterproof cover up Then find [...]

By |2024-05-11T17:56:43+00:00May 8th, 2024|Troubleshooting|Comments Off on Multihead weigher main vibrator replacement steps

The method of maintaining main board’s power

Remove all feed hopper and feeder pan of multihead weigher Record the location of the waterproof cover so that you can quickly mount it back to the same location Remove all dust ring of waterproof cover Find the solid screw on the waterproof cover and remove it all Then lift the waterproof cover up Then find [...]

By |2024-05-12T02:44:31+00:00May 7th, 2024|Troubleshooting|Comments Off on The method of maintaining main board’s power

How to check load sensor

Tools to be prepared:M10 sleeve,hexagon wrench NO.4,hexagon wrench NO.5,hexagon wrench NO.6,cross screwdriver 1.Remove the aluminum specimen box from multihead weigher. 2.Observe the gap between sensor protection sheet. 3.Hang back weigh hopper and check whether the screws on both sides of the weigh hopper will touch the aluminum specimen box or not.If yes,then need to loosen the [...]

By |2024-05-12T02:48:46+00:00May 7th, 2024|Troubleshooting|Comments Off on How to check load sensor

How to set multi times weigh of multihead weigher

First, open recipe(for example, if use 10 head weigher weigh 4000g, weighingtwice, open recipe of weighing 2000g) Open the first page of parameter setting interface, change target weight to4000g. Find parameter of “Multi Combine Times” in the second page of parametersetting interface, change to 2. Click the button in the parameter setting interface, then enter the function [...]

By |2024-05-19T03:22:27+00:00May 6th, 2024|Troubleshooting|Comments Off on How to set multi times weigh of multihead weigher

Frequency converter setting

1.Check weigher frequency converter setting 2-00:d1, frequency enter source, by external current 0-10v 2-01:d2, operated by external terminal. Keyboard STOP can work. 4-04:d2,M0: run/stop, M1: forward/reverse 1-00:60 1-01:60 2-00:d1, frequency enter source, by external current 0-10v 2-01:d2, operated by external terminal. Keyboard STOP can work. 4-04:d2,M0: run/stop, M1: forward/reverse 1-00:60 1-01:60   1-09 the first acceleration time [...]

By |2024-05-12T04:00:43+00:00May 5th, 2024|Troubleshooting|Comments Off on Frequency converter setting

How to plug correctly after replacing the circuit board

1.Open the cabinet which is on the face of switch as below picture, and find out power supply. 2.Then measure 203+ and 203- by multimeter, valid voltage should be DC24V . 3.If the voltage is 24V, which means the power supply is no problem, the problem will be either screen or the cable which connect between cabinet [...]

By |2024-05-12T04:40:47+00:00May 4th, 2024|Troubleshooting|Comments Off on How to plug correctly after replacing the circuit board

How to solve failure of touch screen-12 head linear weigher

1.Open the cabinet which is on the face of switch as below picture, and find out power supply. 2.Then measure 203+ and 203- by multimeter, valid voltage should be DC24V . 3.If the voltage is 24V, which means the power supply is no problem, the problem will be either screen or the cable which connect between cabinet [...]

By |2024-05-12T04:51:16+00:00May 2nd, 2024|Troubleshooting|Comments Off on How to solve failure of touch screen-12 head linear weigher

The fault processing method for all hoppers open door twice

Firstly, take down the No.1 aluminum box, find motor position line and measurethe voltage to see whether there is about 18 v DC by a multimeter. If there is no 18 v voltage, open the machine frame that is on the right of the emergentstop button Find out the main board of multihead weigher, there is [...]

By |2024-05-12T04:57:49+00:00May 1st, 2024|Troubleshooting|Comments Off on The fault processing method for all hoppers open door twice

Title

Go to Top